Lift System Parts
Goshen Main/Lead Cable
SKU: PA-GOSHMAINCABLE
$84.00
Part details
CRITICAL: Please Read Before Ordering
- This is a custom-made cable and is NON-RETURNABLE / NON-REFUNDABLE.
- Allow 2–4 weeks for manufacturing before the cable ships.
- We hold orders that are missing required information to prevent shipping the wrong cable.
A small difference in the model name can mean a different cable size. For example, models “123”, “123AA”, and “123AC” may all use different cables.
If you enter an incomplete or incorrect model, you will receive the wrong cable. No exchanges or refunds will be issued.
You must verify your model before ordering. Use our
Goshen Model Lookup Guide to find your exact factory model name.
How to Order: Required Information
To build your cable correctly, you must provide the following using the required fields on this page:
- Your camper’s Year, Make, and complete Model (e.g., 2005 Rockwood 2280). Enter the model exactly as printed on the factory label.
- Whether your camper has a front or rear storage compartment.
Where to find the exact model name: VIN/data sticker on the tongue or front roadside/curbside wall;
a factory label inside a cabinet door (galley/wardrobe) or near the entry; the original build sheet/owner’s packet.
Do not use dealer marketing names or trim packages.
Can’t Verify Your Model?
If you can’t confirm the exact factory model, submit the three measurements instead (we’ll build to your trailer):
- A. Winch to front of master tube
- B. Length of master tube
- C. Around the back pulley
Diagram & instructions:
Goshen Cable Measurement Guide.
Measure on the trailer (not the old cable), in inches, with the roof safely supported.
About the Goshen Lift System
The Goshen system uses a single main cable operated by a brake winch to drive corner push springs. This replacement main cable restores operation when the original has snapped or frayed.
Commonly Found On (Reference Only):
- Camplite / Damon (Since 1993)
- Dutchmen (1993–2003)
- Forest River (Since 1993)
- Palomino (Since 1987)
- Rockwood / Flagstaff (Some models since 1994)
- Skamper (Since 1977)
- Starcraft (1993–2008)
- Sunlite (1987–1994)
- Sylvan Sport (Since 2008)
- Van American / Cobra (1989–1990)
- Viking (1995–2012, 2018–Current)
Installation: How to Replace the Main Cable (6 steps)
Important: The roof must be in the DOWN position before beginning, to release pressure from the system. Letter call-outs like (K) refer to the series diagrams on our Goshen Lift System Guide.
First, open up the rear spring tubes:
- Remove the tie plate by removing (2) self-tapping screws — see (K) on the diagram.
- Remove the two (2) screws attaching the spring tubes to the master tube (L).
- Remove two (2) screws each from the floor plates (N) attaching the spring tubes to the frame.
- Pull the spring (P) out from the bottom of the telescoping posts.
- Pull the spring assembly (2 springs attached) out of the master tube (L).
Then replace the cable:
- Hold the spring pair, lay the crimped end of the new cable and pusher plate over the springs, and insert both into the master tube.
- Run the cable around the pulley (M), insert it into the master tube, and feed it forward. Clear grease if necessary.
- Make sure the pusher plate is in front of the springs.
- Wrap the cable once around the winch drum, secure it under the cable keeper (I), and tighten the bolt (T) securely — see the cable attachment method inset on the diagram.
- Reassemble the spring tubes, master tube, and tie plate.
- Raise and lower the roof several times to verify operation. You can add new grease to the master tube. If the front and back of the roof do not rise evenly, adjust the pulley (M).
Full guide with diagrams, maintenance tips, and troubleshooting: Goshen Lift System Guide.
Listed fitments (27)
Check your model, lift system and cable position against these listings and the part details.